Electronic Book Readers

Build Wind GeneRator

Is it possible to do build a wind power generator to turn a small electric motor?

The quoted question is:

Build a wind power generator that will turn a small electric motor out of everyday items if possible.

N.B. You cannot use anything that is typically found in a science lab.

Yes, absolutely. What's more, it's actually quite easy. You won't get significant amounts of power out of it but it will run a very small electric motor so long as you use a generator that is significantly larger than the motor you are driving.

You'll need something that you can use for windmill blades and a motor that you can drive as a generator.

The best and easiest solution is to use a radiator fan from a modern car. Most modern cars use electrically powered fans and this is perfect for you because it takes care of the fan assembly and the generator in one go without the need for a complex assembly procedure. They are cheap and easy to get hold of too. Any car wreckers should be able to sell you one for under $20.

This type of fan is not the ideal configuration for capturing wind (they are designed to generate airflow from electricity, not electricity from airflow) but the advantages you get from simplifying the construction process more than makes up for this. Also, as far as I am aware, they are all DC motors which is exactly what you need.

Because a generator is identical in construction to a motor, this fan will generate electricity for you without any need for modification. All you have to do us hook up your small hobby motor to the terminals of the fan motor and put it somewhere where there is enough wind to get the fan spinning. You should be able to generate up to 12v depending on how fast you can get it spinning. If you find that it takes more airflow than you can manage to get it spinning fast enough, you can always construct a ram scoop (like a big funnel with the wide end open and facing the incoming wind and the fan across the narrow end) so that the wind is scooped in from a wider area and forced through the fan at higher speed. This doesn't need to be that strong, corrugated cardboard (like you get from cardboard boxes) would probably do the trick.

So long as you get the fan spinning at a reasonable rate, you should be able to easily power a small motor. Of course, as soon as the fan slows or stops, so does the motor so it's not really a viable solution for real world applications. It should be fine as a simple experiment to demonstrate wind power though.

If you want it to be a bit more practical (i.e. actually work in the real world rather than it just be for demonstration purposes), it would probably be better to run the motor from a battery and use the generator to recharge the battery. This is how proper wind powered systems work. However, the setup becomes more complex when you do this and some circuitry is required to manage the recharging of the battery, among other things, so unless you have some experience with electronics, I wouldn't advise it.

It sounds like this is outside of the parameters of your experiment anyway.

The motor you are going to drive should, ideally, be able to run on voltages between about 3VDC and 12VDC but cheap and easy to find motors like this one (http://www.jaycar.com.au/ShowLargephoto.asp?id=3255&IMAGE=) that is designed to run on voltages from 3V to 4.5VDC will still probably work OK for your purposes. If it is fed 12V continuously for long periods of time, it may overheat and burn out but, considering your setup, it will probably last at least long enough to meet your needs. If you do go for a low voltage motor like this and you want to make sure you don't damage it, just make sure that you don't spin the fan too fast and monitor the temperature of the motor. If it starts getting hot (i.e. too hot to touch), stop it and let it cool down for a while before you start it again. It's not too big a deal if you do burn it out though, these motors retail for about $2 so you won't exactly go broke if you kill it.

Good luck with it.

Hope this helps.

TV

How To Build A Wind Generator - DIY Turbine Plans That Work!

Building Wind Generators is Easier Than You Think

If I had to pick any of the renewable energy methods when starting out again I would start out with building a wind generator. If you were to compare the cost of building solar panels to the cost of building a wind generator you would see that the wind generator options costs about 20% of the solar panel option. To cost to build solar panels that will produce 1000 watts would be around $900 while the cost of a wind generator is only $150 - $200.

That being said, you will need to live in an area where you get at least 12MPH winds in order to run your wind generator though. For most people it shouldn't be a problem; however, there are some places where the wind simply doesn't blow very much.

A wind generator is made up of three "main parts": the motor, the blades and tail, and the tower. The tower can be found for free. Simply drive around your neighborhood looking for somebody who has a satellite dish and a television tower. Ask them if you can have their TV tower. In most cases they'll say yes and in some cases they'll give you money to tote it away (we got $50 when we removed our friends tower).

The motor is fairly easy to find. Simply log on to eBay and do a search for ametek motors. They're not always listed, but you should be able to find one if you keep searching. You'll want one that produces 24 - 48 volts at around 400 - 600 RPM's.

The blades and tail are also very easy to find. Go to a construction site and see if they have any left over 6 or 8 inch blue sewer pipe. You'll only need a piece that's 6 feet long or so, and many times they'll give it to you for free. The tail is made out of a piece of steel rod and a triangular cut piece of plastic. You can find these items at your local hardware store. Make sure to pick up some UV paint to paint the blades and tail piece with. Being constantly exposed to the sun can make the blades brittle and the UV paint protects against that.

You will need some other nuts and bolts from the hardware store as well as a flange so that you can mount the wind generator on the TV tower. TV towers are great because they have a nice 2 ince hole in the top which makes mounting a cinch.

Like I always say "if we can do it, than anyone can". If you can handle a jig saw and follow instructions then you'll have no problem building a wind generator.

About the Author

Andrew Oke is very interested in renewable energy.He has 16 years experience living off the grid, and has completely built his own renewable energy system. Visit his website at Building Wind Generators

Tags: build wind generator, build wind generator alternator, build wind generator free, build wind generator free plans, build wind generator from alternator, diy, energy forever, howto, power how, wind, wind generator

Categories: Compare Ebook Readers

---

Comments are closed